7-Level Communication Builder
7-Level Communication Builder

7-Level Communication Builder

Brand/Manufacturer: ENABLING DEVICES
Save

This product is on backorder and will be available to purchase once it is back in stock.

The 7-Level Communication Builder is a self-contained communication device. It allows the user to record and play back one, two, four, eight, or 16 different messages per level. There are seven levels for recordings, giving a total of up to 112 messages (in the 16 window setting). The unit comes equipped with five sturdy frame or overlays in one, two, four, eight and 16 windows. Re-recording is required when user change window frames.

Features

  • 7-Level Communication Builder requires 4 AA batteries
  • Frame size is 8-1/2" x 7"
  • Size: 12-1/2"L x 9-1/4"W x 4"H
  • Total record time is 300 seconds
  • Pictures not included
  • Time per level by window setting, using all seven levels:
    - 1 Window setting = 42 seconds per segment per level
    - 2 Window setting = 21 seconds per segment per level
    - 4 Window setting = 10-1/2 seconds per segment per level
    - 8 Window setting = 5-1/4 seconds per segment per level
    - 16 Window setting = 2-1/2 seconds per segment per level

More Information

  • Operation:
    - Carefully turn the device over to reveal the battery compartment. A small Phillips head screw must be removed from the battery compartment cover in order to slide it off. Observing proper polarity, install four AA alkaline batteries (Not included) into the holder. Replace battery compartment cover and screw.
    - Place your icon grid over the black message pad area then install the appropriate Velcro backed window frame. Next turn your Frame selector knob to the appropriate setting. Please note pre-made grid layouts can be made with MayerJohnsons Boardmaker program. Our Item No. 4008 for Macintosh computers and item No. 4009 for PC computers. If you have older versions of Boardmaker you can download the pre-made grids from www.MayerJohnson.com. The Template to use on Boardmaker is the Laptop Communicator.
    - Turn the unit on by turning the “ON/OFF/VOLUME" knob into the “ON" position. You will hear a slight audible click as you turn the knob.
    - The microphone is located on the bottom of the unit next to the red “RECORD" button. To record, depress and hold the “RECORD" button first, then depress one of the message pads holding both simultaneously and speak into the microphone (your mouth should be approximately 4-6" from the microphone). Release both buttons once recording is over. Playback your message by pressing and releasing the same pad used to record. Each of the remaining message pads can be “programmed" in the same manner. (The unit will retain recorded information indefinitely, even if the batteries are disconnected. Previously stored information will be erased only when a new recording is performed on the pad.)
    - Adjust playback volume by rotating the on/off “VOLUME" control knob to desired level. Turn the unit off by rotating the “VOLUME" control knob counterclockwise until you hear an audible “click". Using the “LEVEL" knob, select level 2.  Repeat procedures for remaining levels.
  • Important Note:
    - Must use the same window setting for all seven levels. (E.G.) you cannot use a four-window grid on level one and then go to level two and use a 16-window grid. If you did when you went back to level one, your messages would not play back properly.
  • Care of the Unit:
    - 7 Level Communicator can be wiped clean with any mild household multi-purpose, non-abrasive cleaner and disinfectant.
    - Do not submerge the unit in water

Customer Reviews

Questions & Answers


 
 
Please enter your and your friends email address below.
Fields marked with * are compulsory
 
*
*
*
*


Submit Cancel
The selected product information has been successfully emailed to your friend.

Thank you for using www.rehab-store.com

Close