Woodway Bariatric Medpro Treadmill

More Information

• The magnetic emergency stop switch consists of a contact-free switch (break contact) which is mounted on the WUS/data monitor or on the handrail.
• The circuit is closed through a magnet. The magnet is connected with a line, which is attached at the clothing of the runner by a clip. As soon as the magnet tears off of the contact-free surface, an interruption of the 230 V - mains supply will be caused and an emergency stop will be initiated. The magnet has to be placed on the red surface within the yellow circle.
• The magnetic emergency stop switch has to be connected with the runner through the line and clip whenever the treadmill is being used.

• The emergency stop switch (mushroom-shaped) is mounted beside the right handrail and is to be used in an emergency. Pressing the emergency stop switch will interrupt the 230 V - mains supply and initiate an emergency stop. Can release the emergency stop switch by raising the red mushroom head.

• In emergencies the treadmill is abandoned in a different way. First jump straddle onto the side-covers in order to let the running-surface move freely underneath the legs. Then stop the treadmill with the normal stop or with one of the emergency stop devices.

• The treadmills are equipped with a current limit control function, which reduces power consumption and increases safety. Main feature is the current limiter after time overflow.
• This means, if the running belt is blocking for more than 10 seconds (this means the motor current limit is exceeded) the motor current will be reduced to 6 A. This is always recommended in case something gets caught in the belt so that the belt will stop automatically. Once the current limit control has been triggered, the torque of the motor is reduced to a minimum to prevent damage to the motor and electric system.

• Key-Points Of Medpro Treadmill:

  Bearings-

  • Almost all of the bearings used in the treadmill are Pre-lubricated and do not need to be greased initially. On a yearly basis, the four bearings located at the front and rear shaft will need to be lubricated.

  Running Belt-

  • The teeth on the bottom of the running belt are Pre-lubricated to aid in reducing noise. There is no need to lubricate the teeth. If running belt is rubbing against the side of the drive pulleys, then a small amount of grease (i.e. Molykote or equal) on the edges of the belt slats will help reduce noise.

  Drive Belt-

  • As in the case of the running belt, the application of grease on the edge of the drive belt is only needed to reduce belt squeak and should be used sparingly.

  Incline System-

  • The incline systems on Woodway Treadmills are greased at the factory. If utilized for many hours or in a very dusty environment, system will need to be checked. If needed, apply a small amount of grease on chains and incline drive racks.

  
  Description of Treadmill Controls-
  Overview and Basic Functions
  
  • The Woodway Treadmill control is equipped with various elements which adjust the speed and incline systems, allowing for complex control sequences and carrying out of safety and monitoring functions together with pulse measurement.
  • The hardware consists of a micro-controller system based on the SAB80C537 with peripheral switching to the motor control and sensory components and to the control interfaces.
  The following control units can be connected as options for parallel operation-
  
  • Function buttons (FASTER / SLOWER / UP / DOWN / STOP / FAST STOP
  • LED display for speed / incline / time / distance / pulse (in preparation) WUS (LCD touch display with menu guide and access to complex functions)
  • Chip card connection component in WUS
  • PC / ECG equipment or similar via serial interface (implementing various protocols) 
  • Measurement and control of speed
  • Measurement of time, distance, and pulse
  • Interpretation of control activities with safety priority control
  • Time control for running programs
  • Interactive pulse control
  • Entry and monitoring of parameters for limit and operating values
  • Operating hours counter for switch-on and running time, total distance, incline mode
  • Monitoring and safety functions

Warranty

Woodway guarantees the repurchase of Woodway Treadmill products for a period of up to four 4 years after original installation.

Customer Reviews