Rolyan Aquaplast-T Watercolors Spring Green Splinting Sheet

More Information

• Precautions for Finished Orthoses:
  - Splint adjustments are to be made only by a healthcare professional. The healthcare professional is responsible for providing wearing instructions and precautions to other healthcare practitioners, care providers involved in the patients care, and the patient.
  - If unusual swelling, skin discoloration or discomfort occurs, use should be discontinued and a health care professional consulted
• Patterning:
  - Patterns can be drawn on all splinting materials with a scratch awl before placing the material in the water
• Cutting:
  - All splinting materials can be cut at room temperature by using heavy-duty shears, or scoring with a utility knife and bending at the scored mark, then completing the cut with a knife or scissors.
  - If more detailed pattern-making is required, it is recommended that the pattern be transferred to the splinting material to make a rough blank. Then heat the rough blank for one-half the recommended time or until material is soft enough to cut with scissors.
  - This method will reduce rough edges and save time with edge finishing.
  - Light splinting materials can be cut at room temperature using scissors.
• Heating: For Aquaplast splinting materials, use a heat pan liner in the bottom of the heat pan or frying pan.
  - Hydrocollator units can be used for large pieces of splinting material.
  - Use a heat pan liner to dip the material into the unit, to ensure that the material does not touch the bottom. Do not leave the splint blank unattended.
  - In addition to hot water heating, Aquaplast materials can be heated in a convection oven
  Note: that dry heating makes the material self-bonding, so no surface preparation is required for bonding. Material that is heated in the oven also becomes hotter than material heated in water; check temperature carefully before applying it to the patient. Heat material without overlapping or folding on a baking sheet with a non-stick surface in a preheated oven as follows.
  - heat at 195° to 205°F (90°C to 95°C) for up to 10 minutes or until transparent or translucent
  Technical Tip: To prevent hands from sticking to Original Aquaplast and Original Resilient, use cold cream or mineral oil on hands or dip hands in cold water.
• Forming:
  - When Aquaplast materials become transparent or translucent in a heat pan, the material is soft and ready to form.
  - When the material is soft, remove it from the water and pat it dry with an absorbent towel. (To avoid towel impressions or lint, cover the towel with a pillow case before drying the splinting material.)
  - Check the temperature of the material before beginning to fabricate the splint on the patient
  Technical Tip: To prevent hands from sticking to Original Aquaplast and Original Resilient, use cold cream or mineral oil on hands or dip hands in cold water
• Cooling:
  - Cold water, cold packs, cold spray, or cold wraps can be used to speed the cooling process.
  Technical Tip: Exercise band that has been stored in a freezer can also be used to speed the cooling process
• Adjustments:
  - Change in contour or design of the splint can be accomplished easily by spot-heating the area by pouring hot water over it or using a heat gun. Care should be taken not to overheat the material when using a heat gun
  - keep the hot air stream of the heat gun moving and do not hold it too close to the material.
• Edge Finishing:
  - Smooth edges by heating the rough edges of the splinting material with a heat gun or dipping the edge into heated water for 5 to 10 seconds.
  - Smooth the heated edges using finger tips or the palm of the hand small amount of hand or body lotion on the finger tips makes smoothing the edges easier.
• Care and Cleaning:
  - Splinting materials The shelf life of low-temperature splinting materials is indefinite under the following conditions:
  - Store at temperatures between 40° and 90°F (4° and 32°C)
  - Store at less than 65% relative humidity
  - Avoid prolonged exposure to light, especially ultraviolet light
  - Avoid exposure to corrosive fumes and ethylene oxide fumes.
• Fabricated splints:
  - The splint will lose its shape in temperatures over 135°F (57°C). It should be kept away from sources of heat such as ovens, hot water, open flames, and sunny car windows.
  - The splint can be cleaned with soap and lukewarm water.
  - The straps can be washed with soap and water, but the adhesive portion should not be moistened.
  - The splint and straps should be allowed to dry thoroughly before reapplication of the splint.

Specification

Customer Reviews