Roho High Profile Sensor Ready Cushion

More About Roho High Profile Sensor Ready Cushion

• ROHO Planar Solid Seat Insert
• Skil-Care Lateral Stabilizer Armrest Bolster
• ROHO Agility Minimum Contour Back System

How to use ROHO High Profile Cushion?

How to Inflat the Roho High Profile Cushion?

• Place the cushion in the wheelchair with the air cells facing up and the non-skid surface of the cover facing down. Consult your prescriber about alternate positions of inflation valves.
• Slide the rubber nozzle of the hand pump over the inflation valve. Pinch the nozzle, turn to open the inflation valve, and inflate the air cells.
• When all of the air cells are inflated and the cushion begins to arch slightly, pinch the rubber nozzle of the hand pump and turn to close the inflation valve completely.
• Remove the hand pump.
• Repeat cushion inflation for all valves.

How To Adjust Your ROHO Cushion?

1. Place cushion on chair, making sure it is centered with air cells up, with air valve in front, left corner (when the user is seated). Turn valve counterclockwise to open.
2. Slide the rubber nozzle of pump over the valve and inflate the cushion until it begins to slightly arch upward.
3. Pinch the pump nozzle and turn valve clockwise to close. Remove pump. (Repeat steps 1 - 3 for remaining air valves on multi-valve cushions.)
4. Have the user sit in the chair, making sure the cushion is centered underneath. The user should be seated in their normal sitting position.
5. Slide your hand between the cushion surface and the user bottom. Lift their leg slightly and feel for their lowest bony prominence. Then lower their leg to a sitting position.
6. Turn valve counterclockwise to let out air, while keeping your hand under the lowest bony prominence of person. Release air until you can barely move your finger tips – no more than 1 inch (2.5 cm) and no less than 1/2 inch (1.5 cm). Turn valve clockwise to close.

Sensor Ready Cushion Owners Manual

How to clean ROHO High Profile Pillow?

• To Clean the Cover: Remove the cover. Machine wash in cold water (30 degrees C) with mild detergent, gentle cycle, or wipe clean with neutral detergent and warm water. Tumble dry low.
• To Clean the Cushion: Remove the cover, close valve and place in a large sink. Hand wash, using mild liquid hand soap, hand dishwashing liquid, laundry detergent, or a multipurpose detergent. Gently scrub all cushion surfaces, using a soft plastic bristle brush, a sponge or a cloth. Rinse with clean water. Air dry. Do not expose to direct sunlight.

Warnings :

• Check skin frequently, at least once a day. Skin/soft tissue breakdown can occur due to a number of factors, which vary by individual. Redness, bruising, or darker areas (when compared to normal skin) may indicate the beginning of soft tissue breakdown. Consult with a clinician immediately
• The cushion and the cover must be compatible sizes and must be used as directed in this manual. If they are not: 1) The benefits provided by the cushion may be reduced or eliminated, increasing the risk to skin or to other soft tissue, and 2) the individual may become unstable and vulnerable to falling
• Do not use an under-inflated cushion or an over-inflated cushion because the product benefits will be reduced or eliminated, resulting in an increased risk to the skin and other soft tissue. If the cushion does not appear to be holding air, or if you are not able to inflate or deflate the cushion, see troubleshooting. Immediately contact your clinical caregiver, distributor, or ROHO, Inc. if the problem persists
• Do not use your cushion on top of, or in conjunction with, any other products or materials, except as indicated in this manual. Doing so may cause the individual to become unstable and vulnerable to falling
• Do not use this cushion as a water flotation device (e.g. a Life Preserver). It will NOT support you in water

Caution:

• Do not use a cover or a repair kit other than those provided by ROHO, Inc.
• The ROHO Sensor Ready Cushion is intended to be inflated only with the ROHO Hand Pump
• Do not modify the cushion or any components. Doing so may result in damage to the product and will void the warranty
• Do not allow oil-based lotions or lanolin to come in contact with the cushion. They may degrade the material
• Prolonged exposure to ozone may degrade materials used in the cushion, affect the performance of the cushion, and void the product warranty
• Changes in altitude may require adjustment to the cushion
• Keep the cushion away from sharp objects
• Do not expose the product to high heat, open flames, or hot ashes
• If the cushion has been in temperatures lower than 32º F (0°C) and exhibits unusual stiffness, allow the cushion to warm to room temperature
• Do not use the inflation valve, the quick disconnect, or hoses as a handle for carrying or pulling the cushion. Carry the cushion with the Yellow Rope, the cushion base, or the carrying handle on the cover

Customer Reviews