Graham Field Lumiscope Lumineb II Features
Graham Field Lumineb II Nebulizer comes with:
- 1 Disposable nebulizer cup
- 1 Mouthpiece
- 1 seven feet Clear Vinyl tubing
- 5 replacement filter
How To Use Lumineb II Nebulizer Compressor?
- Place your Lumineb II on a flat and stable surface. Be sure that you can easily reach the controls while you are seated
- Gently twist the top part of the nebulizer assembly counter-clockwise to disassemble the nebulizer
- Fill the bottom section of the nebulizer with the medication prescribed by your physician. Be sure that the nebulizer cone is put inside the bottom section
- Replace the top part of the nebulizer and gently twist clockwise to reassemble the nebulizer. Make sure both sections are connected properly
- Attach one end of the air tube to the base of the nebulizer
- Attach the other end of the air tube to the air outlet on the top of the Lumineb II
- Attach the standard mouthpiece to the top of the nebulizer assembly
- If using an optional mask, attach the mask to the top of the nebulizer assembly
- Make sure the On/Off switch is in the Off position, then plug the power cord into an electrical outlet
- Flip the On/Off switch to the On position to begin your prescribed treatment
- When your treatment is finished, shut off the Lumineb II and unplug it from the electrical outlet
Note:
The compressor motor has a thermal protector which will shut off the unit before it overheats. When the thermal protector shuts the unit off
- Switch off the Lumineb II
- Unplug the unit from the electrical outlet
- Wait 30 minutes for the motor to cool down before another treatment
- Make sure the air openings are not obstructed
Cleaning Lumineb II Nebulizer
- Disconnect the air tube, nebulizer, and mouthpiece
- Gently twist the nebulizer to open it
- Rinse the nebulizer and mouthpiece or mask with water
- Dry with a clean soft towel or allow to air dry
- Reassemble the nebulizer when completely dry
- Wipe the compressor with a damp cloth and allow it to air dry
- Never use powdered cleaners or soap pads on the compressor, as it may damage the finish of the unit
Disinfecting Lumineb II Nebulizer Compressor
- Use one part white vinegar to three parts distilled water. Make sure the mixed solution is enough to submerge the nebulizer and mouthpiece
- Wash the nebulizer, mouthpiece, and/or mask in warm water with a mild detergent, then rinse the detergent solution out with hot tap water - Submerge the cleaned components in the water and vinegar solution for thirty minutes
Changing the filter
- Use only Lumiscope nebulizer filters
- Do not substitute cotton or any other materials. Do not wash, clean or re-use a filter
- Never operate your Lumineb II without a filter
- Change the filter every 30 days or when it turns gray
How To change the filter
- Remove the filter cover on the top of the compressor unit - Replace the old filter with a new one
- Replace the filter cover
Lumiscope Lumineb II Nebulizer Compressor Specifications
Particulars |
Dimensions |
Method of Nebulization |
Piston Driven |
Power |
120V, 60 Hz |
Operating Temperature |
50F to 104F (10°C) |
Operating Humidity Range |
10 - 95% RH |
Storage Temperature Range |
-4°C) |
Storage Humidity Range |
10-95% RH |
Weight |
3.3 lbs (1.5 kg) |
Width |
7.75" (195mm) |
Height |
6" (150mm) |
Length |
8.5" (210mm) |
Compressor Pressure Range |
30- 36 PSI (210 - 250 kPa / 2.1 - 2.5 bar) |
Operating Pressure Range |
8 - 16 PSI (50 - 100 kPa / 0.5 - 1.0 bar) |
Flow Range |
6 -8 LPM |
Particle Size |
4um |
Average Nebulization Rate |
0.2ml/min |
Capacity (nebulizer) |
5ml |
Sound Level |
60 dBA |
Warranty
Five year limited warranty