Winco Three Position Drop Arm Convalescent Recliner

How to Assemble Winco Convalescent Recliner?

Back Installation

• After checking your product for any shipping damage, chair needs to be positioned upright on level surface. Remove packing material and hardware. Cut tape and plastic with scissors, being careful not to damage upholstery.
• Slide the Back Frame over the 7/8" tubes of the Seat Frame.
  Note: To ease assembly, spray the Seat Frame Rail ends with WD-40 (or similar lubricant approved by your facility).
• Depress the 1/4" Snap Button in Seat Frame while pushing down on one side of Back Frame.
• Repeat procedure on opposite side until both Snap Buttons are snapped into corresponding holes of Back Frame.
  Note: Snap buttons must protrude out of holes on back frame.

Operation of the Chair

• Non Restraint: To make the chair permanently non-restraint, remove the Snap Button of the Right Tray Arm, and unbolt the Position Lock Bar from the back of the chair.
• Position Lock: Attendant may hold the chair in a reclined position by engaging the Position Lock. To safely accomplish this, recline the chair to the 2nd or 3rd recline position and lower the position lock with your hand until the notches on the Position Lock bars engage with the Position Lock Pins. To release Position Lock, raise the Position Lock off of the Pins and return chair to upright position.
• To ensure proper operation of the reclining mechanism, lubricate all pivot points with a silicone lubricant at least twice yearly.

Operation of the Tray

• Slide the Tray Arms are inserted into the Tray Receiving Tubes (under Armrests on chair). The Tray automatically locks into the first position; depress the Snap Button (on Right Tray Arm) for 2 more positions.
  Note: Left and right are based as if you are seated in chair.
• The Right Tray Arm is movable to compensate for minor variations in the width of the chair.
• Storing the Tray; Insert the left tray arm tube into the right tray receiving tube and the Snap Button will lock it into place. Allow the right side of the table to hang down vertically on the right side of chair (Left and Right; as if you are seated in chair).

Cleaning Instructions

• Remove grime, hair and body oils; Your furnishings should be cleaned with mild soap and water solution and a damp cloth on a regular basis (especially where skin and hair make contact with upholstery).
• Avoid harsh detergents or chemicals that could damage the upholstery or finish of your recliner.
• If the furnishing is disinfected with chemicals or bleach, it mus be wiped off using only clean water on a damp cloth and then be allowed to air dry. Failure to rinse upholstery with clean water can result in a build-up of residues over time that can dry out the upholstery and cause changes to the look and feel of the upholstery and eventually can lead to cracking.

Winco Drop Arm Convalescent Recliner Specifications

Winco Warranty

• Limited One Year Product Warranty: 
  - Winco Mfg., LLC warrants the complete product for one (1) year. At Winco Mfg., LLC sole discretion, it may repair or replace any components freight free that are found to be defective during the first year. Winco Mfg., LLC shall not be liable for any labor, or any other costs incurred as a result of or in conjunction with a warranty claim.
• Limited Three Year Warranty: 
  - Winco Mfg., LLC warrants recliner mechanisms, electrical components, vinyl panels and vinyl on upholstered parts [from cracking or delaminating] pressurized gas springs and casters, when new, for a period of three (3) years. At Winco Mfg., LLC sole discretion, it may repair or replace components found to be defective. Winco Mfg., LLC shall not be liable for any labor, shipping or any other costs incurred as a result of or in conjunction with a warranty claim. 
• Limited Lifetime Chair Frame Warranty:
  - Winco Mfg., LLC warrants steel and aluminum base frames for all products, when new, for the lifetime of the original purchaser. This limited warranty does not apply to paint/finish or any components attached to the frame such as; upholstery, foam, casters, mechanisms or related parts that are covered under above warranties. Winco Mfg., LLC shall not be liable for any labor, shipping or any other costs incurred as a result of or in conjunction with a warranty claim.  

Customer Reviews